How to prepare your house for interior painting
Let's go over the steps you can take to prepare your home for a painting project
1. Do you offer external wood staining for weather protection. 2. We've had damp proofing to our home in the past, and it's starting to come back, although not as bad. There are a few sections (3 levels) however only a few patches which need damp repair. 3. Painting over after damp proofing 3 separate quotes would be ideal
Scrape off all loose paint open all cracks , prime and fill Cut all expansion gaps and fill with Sikeflex Rubberseal all parapets and areas where fine crack appears Repair and use anchoring cement for all major cracks clean gutters and repaint facias Prime and seal all repaired areas Attend to damp problems Paint all wall with 2 coats of plascon wall seal on house and boundary walls Check waterproofing on roof side of parapet Optional extra ( roof special) Rubberseal ridge capping Check for broken tiles Waterproof all joints and valleys ( including garage roof Coat entire roof with 2 coats
+- 50m2 - Durbigum OR Torch-on (ABE). Need a quote for the bill of quantity - hence there is no need to have people contact me. A Bill of Quantity is to establish costing. Once the client approves the estimate then an appointed contractor is informed. Pricing - includes material & labour. Draws are paid on progress and not a deposit - that tells me a contractor is not positioned financially - material on site is another matter altogether. See JCB for standard contractual info.
I have a flat corrugated roof on my outbuilding, I have issues where water is dripping down the walls when we have excessive rainfall, recently hire a pro who use rubberized waterproofing and did not do a good job, so I am a lost for words and who and what to trust. I am in need of a professional that will do a good job. Please feel free to contact me for more info. Thank you
The water is getting under the belcony tiles which has caused dampnest of my wall and the paint is pealing off. It's only 6sqm the tiles has to be removed, and torch-on bitumen applied then re-tiled. I want it done as soon as the walls and the belcony has dried completely. Because the last guy that did it said it would last 10 years and it's not even 6, the second picture is to show the state of the walls directly below the belcony. Apologies for my tone but I'm drive texting I won't have time later to do this. But you can send me the qoutes incase I'm unable to answer when you call as my days are usually extreme. Thanks so much for your time.
What we need is to have a comprehensive quotation: Stating the flow/project steps to be followed: I.e. Removal of old strips; preparation (type); application (process), around washing lines?; against parapet walls; securing of edges on sides of parapet walls; stormwater downpipes. stating the type of product (pamphlet/info brochure) to be used, the guarantee provided on the workmanship and on the product, the required annual/other running maintenance required the expected project time-frame OHS plan and requirements to ensure safety References & contact details This will include the entire roofed are, incl. balcony tops, store rooms & tops, and all parapet-wall tops on roof.
1)Sika Cemflex reinforced waterproofing on 'Cemflex' membrane or simmilar approved applied in strict accordance with manufacturers details including waste (35m2) 2) One layer of DERBIGUM SP 4mm fully sealed to deck by torch on fusion or coldbond 90 ADHESIVE SPREAD at the rate of 1-3sqm per Litre depending on absorption of the surface. Side laps at 75mm and end laps at mm sealed together by torch on fusion. Vertical and horizontal turns should be fused to the primed surfaces; angles; outlets fillets and flat edges. All as recommended by DERBIGUM (m2) 3)Two coats of co polymer or bituminous aluminium paint (m2)
Waterproofing to the balcony: Aluminum doors will be removed to the balcony Aluminum doors and frames will be wrapped in bubble wrap and stored in the garage for safekeeping until re-installation. All cement and waterproofing layers will be chopped up and removed off-site from the balcony. Rubble skip will be on-site and removed once it is filled. All existing waterproofing will be removed. mm Turn-ups will be chopped off in order to apply the waterproofing application onto the bricks. Existing outlets will be removed. New 63mm Flange outlets will be fitted to the parapet walls to allow water to discharge outside of the balcony. Screed-to-fall will be done to ensure water runs out of the outlets, and that there will be no water ponding in any areas. 50x75mm Angle will be fitted where the door will be fitted to prevent water from running back into the rooms. The waterproofing application will consist of the following: x2 Coats of Mapei-Lastic Mapei-tape to all turn-ups and corners and into the cavities. Mapei-net the flat surface x1 coat will be applied, followed by the Mapei-net and Mapei-tape being applied on top of the 1st coat. 2nd coat will be applied over all of the above-mentioned after 24 hours. Aluminum doors and frames will be re-fitted. Turn-ups and bands around the frames will be plastered to a smooth finish. Waterproofing application and plaster will be left for x3 days before the painting and tiling can commence. New tiles will be installed.
Waterproofing to the balcony: Aluminum doors will be removed to the balcony. Aluminum doors and frames will be wrapped in bubble wrap and stored in the garage for safekeeping until re-installation. All cement and waterproofing layers will be chopped up and removed off-site from the balcony. Rubble skip will be on-site and removed once it is filled. All existing waterproofing will be removed. mm Turn-ups will be chopped off in order to apply the waterproofing application onto the bricks. Existing outlets will be removed. New 63mm Flange outlets will be fitted to the parapet walls to allow water to discharge outside of the balcony. Screed-to-fall will be done to ensure water runs out of the outlets, and that there will be no water ponding in any areas. 50x75mm Angle will be fitted where the door will be fitted to prevent water from running back into the rooms. The waterproofing application will consist of the following: x2 Coats of Mapei-Lastic Mapei-tape to all turn-ups and corners and into the cavities. Mapei-net the flat surface x1 coat will be applied, followed by the Mapei-net and Mapei-tape being applied on top of the 1st coat. 2nd coat will be applied over all of the above-mentioned after 24 hours. Aluminum doors and frames will be re-fitted. Turn-ups and bands around the frames will be plastered to a smooth finish. Waterproofing application and plaster will be left for x3 days before the painting and tiling can commence. New tiles will be installed.
Please I would like to have a quotation of a building that has a floor and ceiling that is damaged because of an air handling unit that is placed on top of timber floor. The ceiling below that floor is also affected. Please I would like to have the following in the quotation: 1. An investigation on the cause and extend of the water damage on the floor/ceiling. 2. On top of the timber floor there is a torch-on waterproof. What is the rate of the waterproof when it is removed and when it is replaced with new. Thank you. Kind regards,