How to choose the right type of fence for me?
Do you need a fence, that will provide security, privacy or aestethics?
My wooden garden gate has perished and has always been too heavy for its frame. It is in direct sunlight all day and exposed to rain so I need advice on material. I think the frame is still ok, but may need to be reinforced into the wall. The dims of the gate itself are 80cm x cm. Photos attached. I can use the existing lock but the slot would need to be cut out. I can use the existing handles. The colour is a dark brown according to estate colours. It does not need to be completely solid; it can be slotted. I can stain it providing I am given advice as to which primer and stain should be used, dependant on material of the gate. The finished item would need to be hung/lock fitted. I am not looking for a high-end product, but certainly one that would last.
Barbed wire (in rolls) to be affixed/secured to retaining structure ''wall'' in order to prevent intruders climbing retaining structure and gaining access to the property. So lengths of razor wire to be affixed to retaining structure/wall in order to prevent intruders from climbing up the structure/wall. Also required in possibly a new fence will razor wire for a small section adjacent to the retaining structure/wall.
This job is to replace an existing wooden gate that has perished. Pictures are attached. Measurements of the gate itself are 79.5cm x cm to the frame. The frame needs to be replaced too. I would need the existing handle and lock need to be transferred onto the new gate and the whole gate and frame installed. The gate need not be identical to the existing one.
One 6,4 meter gate. More or less One 2.7 meter. More or less. The two gates must meet. The long gate must be in front of the garage doors. Then other gate can be pushed open . We have a caravan that must be able to pass through the small gate. The attachment between the two gates must be able to go down when taking out the caravan.
contractor that will be able to remove the existing fence and install a new Steel Palisade fence at the Tsheesebe Primary School in Waterberg District Municipality 3. STEEL PALISADE FENCE AND ACCESSORIES SPECIFICATIONS 3.1. Installation of Steel Palisade Fencing Panels: 1.8 x 3m above ground level. 3.2. Fence bearers: 40 x 40 x 2m angle iron. These are to be placed mm from top of paling and mm from bottom of paling. (mm from ground level). These are to be welded flash with the back of the post. 3.3. Palings “Devil Fork” 21 palings per panel. 30 x 30 x 2mm steel angle iron paling 1.8m high. Paling to be inserted and firmly welded to the bearers at mm centres to be centre. Top of the paling to provide a “Devil Fork” effect and bottom will have a dove tail. 3.4. Installation of 2.4m high (76 x 76 x2 mm) Posts: 76 x 76 x 2mm steel square tubing with closing pyramid caps on top. Post must be 2.4m high and mm will be planted into concrete footing to Engineer’s design. 3.5. Installation of Palisade Gates for Pedestrian and Sliding Gate 3.5.1. Sliding Gate: 5 m wide x 1.8 m high. 40 x 40 x 2 mm 4 m wide x 1.8 m high. 40 x 40 x 2 mm Post to be founded in a concrete footing x x deep. Concrete strength to be 20Mpa (minimum) at 28 days. 3.5.2. Pedestrian gate: 1.2 m wide x 1.8 m high. 40 x 40 x 2 mm 3.5.3. Painting: Clean surface and allow to dry completely. Remove all Flux, Rust, Grease and loose material before painting. All joints must be smoothed. Apply one coat Primer for steel (red oxide) and apply one coat universal undercoat and one coat Gloss Enamel (Traffic Green as specified by the LPDE) No brush painting. 3.5.4. The School has perimeter of metres N.B. the tenderer must price for Installation Labour Only, Including the concrete footing; the fence will be supplied by the fabricators.
Good morning Can you please send me a quote for 4 x 2.4M x 3 M x 20 PALES PER 3 METER /SPIKES=SPEAR 30 X 30 COLDROLL ANGLE panels 1 x 2.4M x 1 M Panels 6 x 3M x 76x76 x 1.6 POST 1 x 0.9 x76x38 Rectangular Tube 1.6 Pedestrian Gate And nut and bolt for mounted all panels mounted to the post Area will be 4M x 3M Am looking for your reply
Hello, I'd like a quotation to install an electric fence on my property. We're sub-dividing a plot in Farmall, so there is an existing perimeter fence, but we'd like to define a new boundary within that with approximately ~m of 18 strand fence connected to the existing boundary. The existing boundary fence (~m) needs a new energizer and possibly some repair. Sketch attached with existing boundary (red); new fence (green); and location of energizer (red circle). Please contact me by email. Regards,
I am looking for fencing for my yard, for a farmland. I am able to arrange pick-up from the supplier. I would also like some advice with regards to how many poles will be needed along with the fencing and with regards to anything else I might need along with the fence. I would also like to know the difference in costing between supply of fencing materials only and supply + installation.
To razor wire a small weak access area on property. Dogs prove a good deterrent as do the sheer height and fencing/security by neighbouring properties. Due to constant Load Shedding, camera, electric fence and security options prove redundant due to their reliance on electricity. As such, I would like to just address the small weak area. Not a very big job but necessary so a visit and subsequent quote would be most appreciated.
Please email me first, we can then possibly schedule a call. I have solar power and I want to be sure that the electric fencing is being powered by the solar panels. I am not too sure about the length of the fence exactly, I will need to speak with someone one on one to discuss exactly what I want done and how much fencing that will take.