Electric fence - glossary of terms
Important definitions regarding electric fences
On the other side is a brick wall with that will join with the fence. The wall is 10mX1,8m. I want razor wire on top of the wall, the fence and the pedestrian gate. This is an enclosure at a church and a créche where the restrooms are. This was vandalized lately. We need to secure the area before we can repair the facilities. it is a mission site in Tswelelang and we would appreciate a discount or donation. There are two NPO's on the premisses. the one is a feeding scheme and the chréche of the MRCC church in Tswelelang
We require the current palisade fence to be cut to allow a gate to be inserted - new support posts cemented in and the gate needs to be manufactured to the size of the opening (Approx. mm) electric fence must be re-fitted following the profile of the gate. Heavy duty hinges and sliding latch to be used with a tamper proof piece of metal welded on the outside covering the latch area
Adequate Electric Fencing on the Front Facing Property Perimeter Fence [incl. Remote Driveway Entrance Gate], ~m in Length / Fence Height from the Ground Plus, Right Side Perimeter Boundary Wall - 2x Split / Open Sections, Total: 40m in length (~38m + ~2m), Boundary Wall/Fence Height.
I am looking for an Easyview fencing quote to secure the perimeter of erf 95 Cato Ridge. See attached diagrams. Perimeter is .9m My client is looking for quotes and I have suggested a medium security 3x4mm clearview fence with square posts to keep out land invaders. Alternate high security as an option would be welcome. The site is inland but does experience damp conditions, please specify metal treatment, powder , galvanised etc. Please also specify options with respect to height. When ready to commence the corners of the site will be pegged out for the contractor as well as inline pegs as needed.
The aperture is 6.5m in total. There are two existing upright walls that the fencing may be attached to. Alternatively, if that is not possible, then it would require three posts in total, but I would have to get your advice on that. I would like it installed as well. The fence will be replacing the broken sections of the wall - as in the pictures attached. It is a section of a perimeter wall that must be replaced with a fence. The height should be between 1m and 1.2 metres. Ideally I would like a representative to come and give me a quote.
Need to secure perimeter of house to be built, could be m if I want the garden to be secured, or less price dependent. Trying to find out what affordable options there are. Wanted clear view but think it's too pricey. Could consider other secure options such as razor or electric... Will likely have gate made locally but happy to get an idea of driveway gate price.
Hi there, I am not % sure about these dimensions yet. We are possibly moving into a new property soon and the fencing would be used to keep my cats in our yard. There is one sliding gate and one swing gate. If you have any alternative fencing options that won't allow a cat to climb over I am open to it. Putting my feelers out from pricing for so long. Do you offer a rental option?
Please email me. I will be able to reply immediately, I am not able to take calls. I am looking to install a small fence on top of a wall, it needs to be tall enough to stop a dog from jumping over it or being able to escape. I am not too sure about the length of then fence I would need someone to come take proper measurements.
Item Description 1 Palisade Fencing - .4 linear meters (49.6m x 31.6m x 49.6m x 31.6m) Acquisition of the materials and items - 2 Meters 60 x 60mm x 2 – 2.5mm steel angle iron with 2.5mm width. - 2.5 Meters 76 x 76 x 1.6mm square poles tubes with 2.5mm width. - 60 x 60 x 2 – 2.5mm top and bottom crossing steel angles. - Security padlock for the gate - Welding or casting of the locking mechanisms at the gate. 2.2 Height of the fence - The height of the fence must be two (2) Meters from the ground - Length of the poles must be 2.5 Meters - mm of the 76 x 76 x 1.6mm poles must be dig or excavated into the ground with concrete. - Poles must be 2 meters away from each other. 2.3 Spacing of the poles and angles. - Spacing in between the 60mm angles must be approximately mm. - The 60 x 60 x 2 – 2.5 mm angle iron must have industrial spike on top. - 70mm poles must be covered and closed with the palisade cap. 2.4 Sliding Gate of the palisade fencing - Size of the gate must be 3 Meters wide and slide. - The gate must be fitted with the 60 mm angle iron track. - The sliding track must be fitted with the stop at the end. - The sliding angle iron must have an allowance of 3.5 meters on one side to enable full slide of the gate. - Gate must be installed to enable sliding. - Must have sliding wheels. - Mechanism to lock and protected lock. - Provide security padlock with three (03) keys. 2.5 Painting of the fence - First coat : Prime coat (black or red) - Second coat: Enamel Paint Blue 2.6 Locking mechanisms - Make a mechanism to enable the fitting of padlock - Provide a security padlock 2.7 Crossing angle iron - Slotted channel must be used for the crosses. - Crossing slotted angle iron must be 60 X 60 x 2- 2.5mm - Crossing angle iron must be welded firmly. 1.8 Size and the construction of the palisade fencing Size of the palisade fencing shall be 49.6m x 31.6m x 49.6m x 31.6m and will be constructed around the prefab building.
The boundary measures 49, excluding the two 1m gates. We will opt for the 3mm wire, 1.8m high fence. 75x50 aperture. Dipped black color. Please can you quote on both the prefabricated fence posts and the standard square tubing with clips. We will need 18x 3m panels 23x posts 2x gates (1m width X 1.8m height) At this point we will likely do self installation, however you are welcome to quote on install if you would like to.