How to deal with water damage on walls
Learn about the common causes of water damage in walls, how professionals repair it, and what to expect during the restoration process to prevent further issues.
Existing quadrant shower rail does not attach properly to the side brackets on the wall. The rail lifts and had in the past caused one of the sh9wer doors to fall and shatter. I installed a new shower door however the problem with the top rail persists. I wouod wondering is someone could assist to remove the old fault shower f.rame and install a new decent one for me
We have a unique water saving product which needs to interface with the hot water pipe going to the mixer of a shower. The products consists of two boxes, one housing a flow switch and a solenoid valve. Work to be done: If the hot water pipe is accessible from the top in the roof then the two pipe attachments of the flow control need to be interfaced with the pipe. If the hot water pipe is not accessible then the tiles need to be removed from the shower wall to get access to the hot water pipe and a small box housing the flow control equipment needs to be fitted to the shower wall. The cable which is used to measure flow and control the solenoid valve needs to be placed between the tiles and fitted to the electronic control which is linked to the AC supply.
Recently my EL on the main DB has been tripping. There is a grid typed inverter(installed 6-8 years ago) with neutral and earth internally bonded before this EL, that has it's own DB board with it's own EL downstream of the inverter. Problem varies in frequency but becoming more frequent. Main DB and EL runs the house. Stove. Geyser. Rooms etc.
Recently had a Mercer inverter installed. Can't understand why green light stops and goes on all the time. This is the 2nd set of batteries he got for me. He doesn't get back to me. I am on pension and have been badly let down and taken advantage of. I cannot afford to pay a large sum of money for a call out. I just need advice please. Deeply disappointed and depressed about the matter. This is not what i bargained for. Thank you.
An electrical installation is a group of items of electrical equipment that are permanently electrically connected together and can be supplied with electricity from the works of an electricity entity or from a generating source. An item of electrical equipment may be part of more than 1 electrical installation. Steps to Install electrical distribution board You must have to install the feeder pipe at first. If you're using metal pipe, place a plastic bushing over the connector threads. Using a tape, pull the electrical feeder wires through the feeder pipe. Leave enough wire to get to the opposite side of the panel.
Good day I am looking for quotes for an electrician to wire a new house with the following scope of work: - Issue COC once job is complete - Connect power from mains to the DB - Wire the DB - Secure all wiring in conduit - The following will need wiring: - About 25 plug points - 1 stove isolator - About 20 lights and light switches Thank you Regards
Good day I am looking for quotes for plumbing services for a new house. The scope of work is as follows: - Issue plumbing COC - 2 geysers - Connect house to main sewer - Connect water from meter to house - Plumbing and toilet installation for 5 bathrooms - Plumbing to kitchen sinks - Plumbing to 2 outdoor taps Material will be supplied. Regards
I would like some residential work done. 1. Remove a current chandelier light fitting and replace with a light and fan fitting. 2. Remove a side light fitting - do want to use anymore 3. Check wiring of the above - current chandelier lights tripping 4. Replace one light with another light 5. Fix a faulty light, switches on but goes off after a while.
We require a new manual change over switch installed at/near the db board. New external water proof plug point installed on the outside wall for the standby generator. Replacement of 1 x day/night sensor operating 2 x LED exterior lights. Replace 1 x "jam jar" light fitting. Remove "illegal" cable installtion to exterior plug point and run new T&E cable from exterior plug point to DB board, through newly installed conduit housed in wall.
Good day, we're looking for a quote on the below listed items. Thank you 1. Supply and Install angle valve for washing machine. 2. Supply and install cistern with new inlet valve and flushing mechanism, replace pan connector on mm outlet and repair leaking tap in main bathroom toilet. 3. Fitting copper strapping onto new stand pipe. 4. Remove outlet of expansion valve out of sewer vent system. 5. Supply and install grid for drain. 6. Supply and install inspection cover on toilet outlet.