What kind of permissions do I need for my electric fence, and where to get them?
Electrical fences are dangerous, so you need to obtain permission before installing them. What are they? Where do you get them?
Hi there I need the following: Removal of an old fence and posts (m) Install new ClearVu fence - 1.8 meters high, 3m wide (m) Intermediate posts to be 3m distance between each. Flat wrap razor wire on top (m) Installation of 6.3mx1.8m high main gate gates to be sliding gates, and be supplied with the lockable device Sliding gate to run on angle iron rail. Must be properly secured with concrete. Gate sizes 6.3m opening. Please quote installation and supply only, you can send it on Whatsapp. Thank you
Good day Can you please give me a ballpark figure for the following items listed below: 6-strand electric fence for the top of front and portion side wall. The front brick wall is a 20m Side prefab wall of about 15m. 12-strand fence for 1.5m corner portion. Energizer required. Plug in garage 12m from gate motor. Installation and compliance certificate. You can just send the quote on WhatsApp, please. Thank you
The overall length of palisade fencing by adding up the 3 sections that need fencing is 13.5m but is required as 3 separate sections. Details of the 3 separate sections that need to be fenced are: 1) 4.3m section between house and vibracrete boundary wall (fixed panel, no gate) 2) 4m section between 2 brick pillars (fixed panel, no gate) 3. 5.2m section between a brick pillar and vibracrete boundary wall (this 5.2m section should be inclusive of a sliding driveway gate. Hope to hear from you soon.
The area to be closed of is a tarred surface left side fence 3m front fence 61m with 6m and 3m opening for gates right side fence 3m Please allow for the 2 gate openings and if you do gates please quote separately. We require the most cost effective mesh fencing quotation with barbed wire on top of 2.8m height. Please do not hesitate to contact me for additional info. Thank you and kind regards
Hi All, Can you kindly quote us on the following, supply and installations between Middelburg and Stoffburg. 1> Diamond razor wire fence 1.8 m high 1. m in length with a razor wire coil on top. Because of steel product theft in the country we looking at a quote on treated poles right through the fence exempt the gate posts. 2> Industrial steel gate × 2 x 6 m 1.8 m high with spikes on top. 3> On a separate > 7. m standard size barbed wire fence fixed with treated poles.
Clearview fence City (or suburb) where you need the service: De Aar Fence length: m Fence height: 1.8 m Will you be requiring installation?: Yes Estimated project start: More than 3 months kindly could you assist us with a quote for installation of Clearvu fencing. Please quote us on your rates for these items below: - Removal of an old fence per meter - (Rates per meter) - Installation of ClearVu fence - 1.8 meter high, 3m width (Rates per meter) - Instalation of 2 2 main gates & 1 small walk-in gate - Gates dimensions (2.4m high & 6m width) - 11-12 meter rail on each main gate X3 Also quote us separately on the gates motors installation (D10 Centurion motors X3) The entire yard is an estimated m end-to-end Sincere Regards
1) Need to heighten existing asbestos-cement fence to fill a gap were 3 burglaries took place over x-mas season. 2) Would also need 3- 5 support poles -circa 3.5 meters. 3) Kindly supply standard width of your metal fence AS WELL AS Palisade fencing and pole prices - No decision yet as which of above two is more secure to intruders PLEASE NOTE - my phone ONLY rings for direct incoming calls - NOT Text or Voice Messages - Kindly ask your agents to PHONE .
Razor wire fence piranha Galvanised a hight of 1.8- meter diamond mash with an open ×mm. high tensile core.BTO-20.supported by a plain wire galvanized 4 mm three line running parallel top middle and bottom. Fencing stel pole standards Y- profile (kSTD1.80).Bitumen coat 3.24 kg /pole .The pole must be installed 3m apart
There is currently prefab walling in place but we wish to remove that and build a brick and mortar wall instead. The fence needs to be detachable to allow a truck to move in and out and lay down materials behind the fence needed for the building of the new brick and mortar wall. We therefore need a temporary fence for the time being to protect us against theft as this is something that has happened twice before and is a major issue. After the brick and mortar wall is finished/built we will need the fence to be removed.
One razor wire diameter height (estimate 0,45m) by 9 slabs (13,5m) on east end vibracrete wall and 7 slabs (10,5m) on back vibracrete wall and another 9 slabs (13,5m) on west end vibracrete wall, totalling to 37,5m in length. Need to supply galvanised fixture brackets, onto each concrete upright post, as well.