The measurements (4 options) I need for the sliding doors are: 3m (L) x 4.5m (w) left and 4.5m (w) 2.8m (L) x 4.5m (w) left x 4.5m (w) right 3m (L) x 4m (w) left x 4m (w) right 2.8m (L) x 4m (w) left x 4m (w)right Please note that the sliding doors will have a pocket in the wall where they stack into when opened. The floor track preferably recessed. The measurements are for doors that meet at a corner 90 degree opening. They can stack separately on either side.
Entrance +/- 84m² - Remove current brick paving. Pave in dark grey square cobble stone with coping Tasting area +/- 73m²- Remove current brick paving. Level the area (remove tree roots) . Pave with cobble stone paving (colour to be forwarded at a later stage) Cottages +/- m²- current area is gravel. Pave the area in front of the cottages as well as 3 parking areas. Approximately 9m² to be levelled. Grey Split pave bevel or norse interlocking paver
Good day, Please help with a quote for the doors below with installation. Should the sizes need to adjust a little to get standard doots that are cheaper then this is fine as well as we still need to break the walls. All of them should be black aluminium. Sitkamer - 4.5 x 2.4 Sitkamer 2 - 4 x 2.4 Sitkamer 2 kant - 4 x 2.4 Stoep - 4 x 2.4 Kids stoep - 4.5 x 2.4 Regards,
Normal front door needs replacement (I am not too concerned about looks, so am open to suggestions as to what type) - currently wood but this is the 2nd door in the last 15 years so need some advice. Current door is damaged/rotting. Will require installation as well. Location : Rooihuiskraal North, Centurion
The size is 4,37m (width) x 2,06m (height). I would like them to stack on the left hand side. I'd like the frames in black and charcoal, and installation included in the quote. The current glass sliding door, and sliding metal gate would need to be removed too, which I'd like included in the quote. I live in Durban North.
Type: old fashioned standard red grey 50 paver (to match existing) 1 ) Driveway to afdak (m2) 2) 2.5 x 8m piece of new paving next to existing 6 x 8m paving (20m2) 3) 2.1 x 12m piece of new paving (25m2) 4) 1 x 9m piece of new paving (9m2) There must be sheeting underneath to prevent bossies growing through.
1.We have existing wood back door with window panel. 2. We have a 2 door with small glass panels. 3. Bedroom window to convert to sliding door. And window panel on 1 of 2 sides. Want to replace all with aluminium or upvc. It also needs to have a mesh door to keep flies, mozzies, cockroaches oout. I would like a golden bronzy colour. Or white. And it must have a guarentee and not be easy to break into. I believe this is a weakness of aluminium doors and windows. And all 3 must have a trellidoor or equivalent in same colour with a rust free guarentee.
Image attached: 1. Front door with padlock and glass panel above. I would like to replace the timber door and possibly the doorframe (if possible). And I would prefer the clear glass panel to be replaced with a solid panel to match the finish of the timber, inside and outside. Ideally all to be painted a medium sheen-black on the exterior and a neutral colour paint finish inside. There would need to be provision for a Yale handlock and a knocker/with knob on the exterior. Please suggest a design with raise and fielded panels - I am also open to the idea of a stable door.
Well the wooden door has Ribbed like glass and on the side wooden frame where the locks meet. That side glass is broken and needs replacing. It's a plain glass as I think it was broken before. But I would like the matching Ribbed glass as the main door for the side broken door. Do you have that in stock and are you in Somerset west? I'm in CBD near Lion square. I prefer communicating over whatsapp.
The existing wooden door which leads onto the balcony from the apartment blocks stairwell was broken off by the wind. We need the frame repaired if damaged and the door which is a hollow door replaced with a solid wooden door but the cheapest one available. The new solid door has to look similar to the other balcony doors in the block, please see the attachment for the design. The existing hinges, lock and door handle can be used on the new door. If the new door can be varnished in the same colour as the old one then please go ahead but if not then no problem, we will varnish it.
