I live in an old Victorian house. It’s a grade IIB listed property. I’ll be doing heritage-approved renovations. I’m looking for a builder that understands the requirements for these old homes as all building work needs to be sympathetic to the materials used in these houses (ie, lime mortar and plaster). Portland cement cannot be used as part of this project. Airplast is a good project that should be used instead, so a builder with knowledge of this product or similar is essential.
**1. Face Brick Double Wall with Pillars (2.4m x 15 mete): ** **2. Face Brick Single Wall (1.8m height x 10): ** - Face bricks (matching existing): - Cement: - Sand: - Labor for construction: **3. Foundation Replacement: ** (15m) - Excavation and removal of existing foundation: - Concrete mix for new foundations: - Reinforcement bars for foundations: - Labor for excavation and foundation replacement:
Remove all existing bathroom floor and wall tiles. Install new shower and tile entire floor with only the wall in shower area to be tiled, remaining bathroom to be skimmed and painted white. bathroom is approximately 7 sqm (en suite). One entire wall (2m x 2.5m) has existing pine cupboards, floor to ceiling. Existing toilet and bidet to remain in place.
I have an existing 12m High Cube container on my property in Betty's Bay. It is intalled on 0.50m plynths and has existing plumbing and electricity. Extend the width by 0.80m along the full 12m length using timber framing Instulate the unit and finish interior with dry wall. Fit 3 x windows (supplied) along timber extention. Fit 1 x sliding door (supplied) at opening end of container Close existing single door opening with container wall removed for extension Roof unit with 0.35m overhang all around
Hi i would like the following done: a. the outside area around the house to be water and damp proved b. the outside area to be tarred and clear fenced c. the driveway from the house to the entrance of the road to be tarred d. the entire house to be sealed and damp protected e. the entire house to be painted f. the bathroom requires: two taps in the bath, the existing sink to be replaced, a full shower fitting with a rod for a shower curtain and a toilet roll holder. e. the geyser to be installed but need to be discussed before purchase f. 2 bedrooms requires built in cupboards e. kitchen needs built in cupboards with sink and taps requires replacing the roof also requires damp proving
We would like to re-do the whole bathroom. Remove the bath and install a shower. replace the tiles on the wall and floor. Replace the toilet and basin and add a floating shelves under the basin. we would also like to re place the ceiling and lights. I want a rain shower as well as a adjustable hand shower. we currently have a shower in the bath but may need to move the pipes to accommodate the new design. We would also like to place the toilet in a different location in the bathroom to make it more spacious. We have an idea of the layout but we are open to suggestions. We would like to start mid March, but would like to work out the budget before then. our bathroom size: cm length by cm width.
Recently had a Mercer inverter installed. Can't understand why green light stops and goes on all the time. This is the 2nd set of batteries he got for me. He doesn't get back to me. I am on pension and have been badly let down and taken advantage of. I cannot afford to pay a large sum of money for a call out. I just need advice please. Deeply disappointed and depressed about the matter. This is not what i bargained for. Thank you.
Afternoon , I do have a project which is supposed to start any time soon its a ground floor with a story on top of the double garage part and the lounge dinning and kitchen part. So it will be having 3 bedrooms on the ground floor 2 will be having ensuites ,a study room, separate bathroom and toilet and also an outside toilet On the first floor is, main bedroom with ensuites and separate toilet , lounge and the veranda part with palisades. In short...
An electrical installation is a group of items of electrical equipment that are permanently electrically connected together and can be supplied with electricity from the works of an electricity entity or from a generating source. An item of electrical equipment may be part of more than 1 electrical installation. Steps to Install electrical distribution board You must have to install the feeder pipe at first. If you're using metal pipe, place a plastic bushing over the connector threads. Using a tape, pull the electrical feeder wires through the feeder pipe. Leave enough wire to get to the opposite side of the panel.
Would like to have an idea of what it will cost to build a simple rectangular shaped house using blocks and IBR sheeting roof, exposed inside roof using poles, concrete "stuco-type" floor throughout. WIDTH - 14 meters wide consisting of 8 meters internal living area, plus 4 meters front patio., plus 2 meters back patio. LENGTH - 25 meters completely open plan for kitchen with laundry and pantry, dining room, lounge (all open plan), and four bedrooms in the last 12 meters
