How much does it cost to repair a fence in South Africa?
The total repair cost will depend on the size, type, and length of the section of the fencing that needs to be repaired.
Good day Kindly send me a quote on the following: Single gate - 0,8 x 2.1 – Clear Vu (Gate located at Retaining wall 6) 2,1m high Clearview Fence, with 60 x 40mm Steel posts every 3m – (per meter rate) The Clear Vu is in and around -m. Supply & Installation at Rockdale Middelburg Mpumalanga.
Good Day, could you possibly give me a rough estimate on pricing for a 6-strand electric fence. Wall perimeter is +-m including 2 gates (1x sliding & 1x double swing gate). The walls are stepped brick walls as well as pre-cast slab walls. I also want to divide the uprights into straight ones between neighbours & kinked ones leaning out on the street boundary (50/50 split). The trees will be trimmed/cut back to allow installation. This is just to get a rough idea before I waste your and my time. Thank you in advance. Regards
Good day, I hope that you are well. May you please forward me a quote for your 1.8m high diamond mesh fence to cover a mxm yard. May you also include a gate of the same height which is about 2.5m long. Kindly include all the material which will be required to erect both the fence and gate. Your assistance will be appreciated. Regards,
Preparation of the site prior to installation, e.g. removal of grass and shrubs. Supply and installation of palisade fencing with gate to cover an area of 36m² (6 x 6 meters) - Fencing must be 2 meters in height (devils fork type). - Fencing and gate posts must be secured into the ground with concrete. - Pedestrian swing gate (at least mm in width) with padlock (1 master and 1 spare key) providing access into the fenced-off area. - Gate to open to the outside of the fenced off area. - Fencing, gate and posts to be treated with rust preventative primer and painted in green. • Removal of any rubble generated by the service provider during the installation of the fence (e.g. empty cement bags, metal off cut pieces, grass or shrubs removed as part of the installation.
The electric fence must be installed on the inside of the current fence at a distance of approximately 0.5meter from the existing fence. Provision should be made for the motorized gate (vehicle entry) complete with gate switch. The electric fence must be equipped with an 8-joule energizer with alarm, strobe light, battery backup and remote-control activation/de-activation. Total height of the electric fence must be at least 2.3m and must be electrified from the bottom to the top. The total length of the existing perimeter fence is approximately meters. A min 2 year warrantee plan on maintenance and Service after installations of electric fence will be required Installation of the electric fence must comply with the installation, material and quality specifications in SANS -3 (including any subsequent amendments) A valid Electric Fence System certificate of compliance (EFC), issued by a registered Electric Fence System Installer (EFSI) must be provided to SAWS upon completion of the installation. Wires will need to be pulled taut at the anchor end (install a self-locking ratchet-style wire tensioner, install a turnbuckle cable tensioner) After everything is attached, recheck the voltage at a point farthest away from the charger/main power source. Supply and install 8-joule energizer with alarm. Each corner of the electrical fence will need to be braced with a supplied corner piece. Supply and install strobe light. Supply and install battery backup and remote-control activation/de-activation. Remove any plants that have grown up along your fence and spray a glyphosate herbicide (like Roundups) to reduce plant growth in the area. Test the fence to ensure its operational after installation.
Hello. I want palisade fencing installed infront of my property. It's 1,5m on one side and 16m on the other side. I do have a tree in front of the property and would like that section to have the fence bent around the tree. I am situated on the bluff. Please contact me when you have a chance. Thank you.
I would like to extend the height of my fence on the one side of my property, however, the wall isnt all one level and has 4 different levels. i would like a wooden topper to connect to the existing wall about a third of the way from the top of the wall, to provide extra privacy. 3 of the walls are 4.5m in length and one wall is 4m in length which totals at 17.5m, but the panels would need to be custom made.
1. Option 1 is the Blocks walling for perimeter fencing at 3km with a height of 2.1m n width of 14omm with shark spiketeeth on top. 2. Option 2 concrete wall panels (6m lengths at 3m height n mm width) for 3km with shark spiketeeth on top. 3. Option 3 clear view fence 3km n 2.1m height with shark spiketeeth on top.
Outer Fence: .81m Inner Fence: .25m Area 1: Parameter .16m Diamond Mesh 2.4m high, x 50 x 2.5mm Straining posts 3m High x x 2mm Stay 3m high x 50 2mm Intermediate Posts 3m high x 50 x 2mm Double Barbed wire Binding Wire BTC Razor Coil mm Bolts & Nuts Area 2: Parameter .35m Straining posts 3m High x x 2mm Stay 3m high x 50 2mm Intermediate Posts 3m high x 50 x 2mm Double Barbed wire Binding Wire BTC Razor Coil mm Bolts & Nuts
Require electric motor gate for driveway to double garages to be included in the palisade wall as well as a pedestrian gate. L shape fence - short side = 8 m - long side = 23 m in total (8 m fence including the pedestrian gate, then 6 m in front of the driveway which needs to be an electronic gate).