What kind of permissions do I need for my electric fence, and where to get them?
Electrical fences are dangerous, so you need to obtain permission before installing them. What are they? Where do you get them?
I want to raise the vibocrete in the back yard with one slab. It's 9.5.m straight (6 and a bit slabs) and the one end 2m ( 1 and a bit) towards the house and then the other end two slabs on the existing wall towards the front of the house. Please quote on that. Kind regards. Photo's attached: 1. back. 2. Left side. 3. Right side
A quotation will need to be on the Following: Palisade Fencing for 15 meters The sliding gate is 4m long and the side gate is mm. No cross members for 5m of the 15 meters Uprights there are 5 and they’re 76mm square tubing Gate frame is 80 x 40 mm rectangular tubing and it’s 4m x 2m with a diagonal beam that’s 4,5m long Also - Pricing per meter on 38mm square tubing.
Fencing m on 0.5ha Supply and install security fence of 1.8m high. Corner posts must be concreted into ground at least mm deep Uprights installed every 4m at least mm deep Y std installed every 24m concreted into ground at least mm deep Fence consist of four-line strong wire at least 4mm thick and 3 lines razor wire. (Not razor mesh) See attached photos.
Electric Fence Entire Perimeter m 8 Strand Wall top electric fence 50 8 Strand Square Tube Brackets (1 every 3m) 1 Energizer 1 Lightning Diverter 1 Siren HT Cable - Slimline Ferrules 6mm/ 48 Tensioner - hybrid Comp spring 48 Spring Hooks 17 Warning signs - small double sided every 10m Aluminium Wire 1.6mm 8 Earth Spikes, every 30m, 3 at energiser for each zone 80 Wall anchors 5m Conduit,connectors 1 Gate Contact Installation
Clearvu or similar and approved high density anti-climbing and anti-cut pressed mesh panel screen, formed of 3mm diameter horizontal and 4mm vertical high tensile wires galvanised with marine fusion bond coating (Colour: Black), with apertures size 76,2mm x 12,7mm and reinforcing V-section ribs, frame formed of 76mm thick square section
1. Energizer with keypad . square tube brackets 8 lines 18- Stays mm with lugs 18- Stay clamps 5-Braided wire stainless steel 1.2mm 3- HT cable slimline black 5- Ferrules 6mm per - Tension springs 2- Spring hooks 50 per pk 2- Standard gate contact 20- Warning signs 12- Earth spikes 2- Lightning diverter
We are looking for flat wrap razor wire to be laid along an existing 1.8m tall Bonnox fence. Quotes should be installed and supplied as two separate quotes. Just a single strip of flat wrap along the top of the bonnox fence. All areas are easily accessible as there is a perimeter road along the fenceline. Please send me quotes via email, no unnecessary calls, please.
Good day. The property is m right round there are 2 motor gates. The garage is not attached to the house. The distance from where the Energizer would be mounted up to the fence is 10 meter. There are enough soil for earthing. The property fence wall is made of rock and cement. The front fence has pieces of palisade devils fork of 2,5 m each for the whole length of 56 meters. The property consist of 4 corners. The property is a Square. Xtras needed: A remote panel to reset the alarm would be good. A siren as well as a strobe light. An indicator light(LED) showing the electric fence is armed.8 Strand electric fence.
1 Area at M/Hills above Pilgrims rest: Mist belt and rust an issue 2 Area 10.0m x 10.0m 3 Hight above ground 2.4m 4 Corner posts: SABS Galvanized 4 5 Stays: Every 2 meters(?) 16 6 Fence: Welded razor wire mesh: SABS galvanized 7 On top of Fence and on ground level (Inside): Double concertina razor wire: SABS Galvanized 8 Lockable pedestrian gate (Per point.5) with high security lock - weather resistant Construction: Concreted corner posts Concrete slab under the whole fence mm Wide and mm Deep Crushed rock on outer edge of slab: mm mm wide x mm Crushed rock inside the fence:40mm 8.5mx8.5mx0.1m
Please qoute me on supply and installation of palisade fence: • Steel Posts: Supply and delivery of hor deep galvanised steel posts, 2.60m long 75x75x2mm with xx3mm welded bottom plate. Units. • Steel Posts: Supply and delivery of hot deep galvanised steel posts, 2.60m long xx2mm with xx3mm welded bottom plate. 2 Units • Supply and delivery of panel made 3m long 25x25x3mm vertical hot deep galvanised angle irons. 38x25x5mm top and bottom angle iron. Angle irons to be welded with 6mm fillet welds on the top, middle and bottom horizontal angle irons before galvanizing and installation.