Clear IBR (?) sheeting over a section of the garage (two car tunnel) lifted in strong wind. Currently held down by a couple of rocks but needs replacement. Perhaps general inspection of rest of roof would be good idea. Also wooden shelter between Kitchen and Garage which is flat, has bitumised (Laycool) (?) top. which has leak. Am concerned water collecting there could cause wood rot. Hasn't had bitumen redone for a year or two Needs redoing.
I’m looking to build a 2 story granny flat, with half of the ground floor being a car garage. The rest of the ground floor should have an open plan kitchen and living area with a kitchen bar counter where 2 people can eat, a powder room under the stairs to the first floor, and sliding doors all across one wall. The first floor should have a bathroom, walk in closet and large bedroom with space for a coach and tv in front of the bed. Nice to haves include wooden floors, air conditioning, large windows, security bars on all entrances to the building and the upstairs, and stylistic stairs. The proposed location of the build is street facing and next to a property boundary wall, it’s important to us that no one can see into the first floor which is above street level, while still getting optimal light. I have attached some inspiration pictures for the layout of the kitchen & bedroom.
A deck sits over my bedroom. The deck has a water feature and has planter trenches built into the low perimeter wall of the deck. There are signs of damp in the ceiling of the bedroom. I suspect the water feature and planter trenches are the source of the damp. I want to remove the water feature and trenches, and ensure that those areas are waterproof.
A deck sits over my bedroom. The deck has a water feature and has planter trenches built into the low perimeter wall of the deck. There are signs of damp in the ceiling of the bedroom. I suspect the water feature and planter trenches are the source of the damp. I want to remove the water feature and trenches, and ensure that those areas are waterproof.
The leak is only on one side of the pitched roof close to the parapet wall. The leak is intermittent depending on the angle of the rain. On inspection the tiles all appear to be in good condition and no cracks were found. It could be something to do with the flashing installed where the tiles meet the wall.
Good day. There is a few things we want to do. 1. Remove old car port and build new one. 2. Break down braai area and build indoor braai with chimney. 3. Extend car port to backyard adding windows and sliding door, and back door. 4. Add lighting. 5. Move outdoor water pipe to the front. 6. Remove paving and add tiles. 7. Remove old artificial grass and add new one. 8. Break down pillar. That's what I recall.
the house is a 7.3x7.3m square, with the front wall height 4.2m (all walls cladded with metal sheeting) and the back wall 3m high. the roof is 7.3x7.4m. id like to request a roofing expert or someone with knowledge of flashing and trim, to quote me for the full installation of metal on all four sides of the building, the roof, and a 7.3x3m lean to stoep roof. the site is in de rust, and doesnt have access to electricity. will need battery operated machines for roofing.
I live in an old Victorian house. It’s a grade IIB listed property. I’ll be doing heritage-approved renovations. I’m looking for a builder that understands the requirements for these old homes as all building work needs to be sympathetic to the materials used in these houses (ie, lime mortar and plaster). Portland cement cannot be used as part of this project. Airplast is a good project that should be used instead, so a builder with knowledge of this product or similar is essential.
**1. Face Brick Double Wall with Pillars (2.4m x 15 mete): ** **2. Face Brick Single Wall (1.8m height x 10): ** - Face bricks (matching existing): - Cement: - Sand: - Labor for construction: **3. Foundation Replacement: ** (15m) - Excavation and removal of existing foundation: - Concrete mix for new foundations: - Reinforcement bars for foundations: - Labor for excavation and foundation replacement:
Remove all existing bathroom floor and wall tiles. Install new shower and tile entire floor with only the wall in shower area to be tiled, remaining bathroom to be skimmed and painted white. bathroom is approximately 7 sqm (en suite). One entire wall (2m x 2.5m) has existing pine cupboards, floor to ceiling. Existing toilet and bidet to remain in place.
