Different types of security fences: Palisade, electric or razor wire?
What are the advantages and disadvantages of different types of security fences
One razor wire diameter height (estimate 0,45m) by 9 slabs (13,5m) on east end vibracrete wall and 7 slabs (10,5m) on back vibracrete wall and another 9 slabs (13,5m) on west end vibracrete wall, totalling to 37,5m in length. Need to supply galvanised fixture brackets, onto each concrete upright post, as well.
I already have a clearview fence installed and I am looking for a barbed razor wire fence for the top of the clearview fence. I have an approximate length but I am not percent sure if that length is correct. This is quite urgent as I am looking for the fence to be installed by the end of this month.
Barbed wire (in rolls) to be affixed/secured to retaining structure ''wall'' in order to prevent intruders climbing retaining structure and gaining access to the property. So lengths of razor wire to be affixed to retaining structure/wall in order to prevent intruders from climbing up the structure/wall. Also required in possibly a new fence will razor wire for a small section adjacent to the retaining structure/wall.
contractor that will be able to remove the existing fence and install a new Steel Palisade fence at the Tsheesebe Primary School in Waterberg District Municipality 3. STEEL PALISADE FENCE AND ACCESSORIES SPECIFICATIONS 3.1. Installation of Steel Palisade Fencing Panels: 1.8 x 3m above ground level. 3.2. Fence bearers: 40 x 40 x 2m angle iron. These are to be placed mm from top of paling and mm from bottom of paling. (mm from ground level). These are to be welded flash with the back of the post. 3.3. Palings “Devil Fork” 21 palings per panel. 30 x 30 x 2mm steel angle iron paling 1.8m high. Paling to be inserted and firmly welded to the bearers at mm centres to be centre. Top of the paling to provide a “Devil Fork” effect and bottom will have a dove tail. 3.4. Installation of 2.4m high (76 x 76 x2 mm) Posts: 76 x 76 x 2mm steel square tubing with closing pyramid caps on top. Post must be 2.4m high and mm will be planted into concrete footing to Engineer’s design. 3.5. Installation of Palisade Gates for Pedestrian and Sliding Gate 3.5.1. Sliding Gate: 5 m wide x 1.8 m high. 40 x 40 x 2 mm 4 m wide x 1.8 m high. 40 x 40 x 2 mm Post to be founded in a concrete footing x x deep. Concrete strength to be 20Mpa (minimum) at 28 days. 3.5.2. Pedestrian gate: 1.2 m wide x 1.8 m high. 40 x 40 x 2 mm 3.5.3. Painting: Clean surface and allow to dry completely. Remove all Flux, Rust, Grease and loose material before painting. All joints must be smoothed. Apply one coat Primer for steel (red oxide) and apply one coat universal undercoat and one coat Gloss Enamel (Traffic Green as specified by the LPDE) No brush painting. 3.5.4. The School has perimeter of metres N.B. the tenderer must price for Installation Labour Only, Including the concrete footing; the fence will be supplied by the fabricators.
Good morning Can you please send me a quote for 4 x 2.4M x 3 M x 20 PALES PER 3 METER /SPIKES=SPEAR 30 X 30 COLDROLL ANGLE panels 1 x 2.4M x 1 M Panels 6 x 3M x 76x76 x 1.6 POST 1 x 0.9 x76x38 Rectangular Tube 1.6 Pedestrian Gate And nut and bolt for mounted all panels mounted to the post Area will be 4M x 3M Am looking for your reply
Hello, I'd like a quotation to install an electric fence on my property. We're sub-dividing a plot in Farmall, so there is an existing perimeter fence, but we'd like to define a new boundary within that with approximately ~m of 18 strand fence connected to the existing boundary. The existing boundary fence (~m) needs a new energizer and possibly some repair. Sketch attached with existing boundary (red); new fence (green); and location of energizer (red circle). Please contact me by email. Regards,
I am looking for fencing for my yard, for a farmland. I am able to arrange pick-up from the supplier. I would also like some advice with regards to how many poles will be needed along with the fencing and with regards to anything else I might need along with the fence. I would also like to know the difference in costing between supply of fencing materials only and supply + installation.
To razor wire a small weak access area on property. Dogs prove a good deterrent as do the sheer height and fencing/security by neighbouring properties. Due to constant Load Shedding, camera, electric fence and security options prove redundant due to their reliance on electricity. As such, I would like to just address the small weak area. Not a very big job but necessary so a visit and subsequent quote would be most appreciated.
Please email me first, we can then possibly schedule a call. I have solar power and I want to be sure that the electric fencing is being powered by the solar panels. I am not too sure about the length of the fence exactly, I will need to speak with someone one on one to discuss exactly what I want done and how much fencing that will take.
I require the supply/installation of galvanized, stainless steel - razor spiked palisade fencing for the front of my property, will serve as a boundary wall (I estimate the length of the fence to be 35m). I will also require a sliding gate that will open/close in my drive way that leads into my double garage.