12 steps to make sure your electric fence will keep intruders out
An electric fence is designed to keep intruders out. Here's how you can make sure it will do just that.
One 6,4 meter gate. More or less One 2.7 meter. More or less. The two gates must meet. The long gate must be in front of the garage doors. Then other gate can be pushed open . We have a caravan that must be able to pass through the small gate. The attachment between the two gates must be able to go down when taking out the caravan.
contractor that will be able to remove the existing fence and install a new Steel Palisade fence at the Tsheesebe Primary School in Waterberg District Municipality 3. STEEL PALISADE FENCE AND ACCESSORIES SPECIFICATIONS 3.1. Installation of Steel Palisade Fencing Panels: 1.8 x 3m above ground level. 3.2. Fence bearers: 40 x 40 x 2m angle iron. These are to be placed mm from top of paling and mm from bottom of paling. (mm from ground level). These are to be welded flash with the back of the post. 3.3. Palings “Devil Fork” 21 palings per panel. 30 x 30 x 2mm steel angle iron paling 1.8m high. Paling to be inserted and firmly welded to the bearers at mm centres to be centre. Top of the paling to provide a “Devil Fork” effect and bottom will have a dove tail. 3.4. Installation of 2.4m high (76 x 76 x2 mm) Posts: 76 x 76 x 2mm steel square tubing with closing pyramid caps on top. Post must be 2.4m high and mm will be planted into concrete footing to Engineer’s design. 3.5. Installation of Palisade Gates for Pedestrian and Sliding Gate 3.5.1. Sliding Gate: 5 m wide x 1.8 m high. 40 x 40 x 2 mm 4 m wide x 1.8 m high. 40 x 40 x 2 mm Post to be founded in a concrete footing x x deep. Concrete strength to be 20Mpa (minimum) at 28 days. 3.5.2. Pedestrian gate: 1.2 m wide x 1.8 m high. 40 x 40 x 2 mm 3.5.3. Painting: Clean surface and allow to dry completely. Remove all Flux, Rust, Grease and loose material before painting. All joints must be smoothed. Apply one coat Primer for steel (red oxide) and apply one coat universal undercoat and one coat Gloss Enamel (Traffic Green as specified by the LPDE) No brush painting. 3.5.4. The School has perimeter of metres N.B. the tenderer must price for Installation Labour Only, Including the concrete footing; the fence will be supplied by the fabricators.
Good morning Can you please send me a quote for 4 x 2.4M x 3 M x 20 PALES PER 3 METER /SPIKES=SPEAR 30 X 30 COLDROLL ANGLE panels 1 x 2.4M x 1 M Panels 6 x 3M x 76x76 x 1.6 POST 1 x 0.9 x76x38 Rectangular Tube 1.6 Pedestrian Gate And nut and bolt for mounted all panels mounted to the post Area will be 4M x 3M Am looking for your reply
I require the supply/installation of galvanized, stainless steel - razor spiked palisade fencing for the front of my property, will serve as a boundary wall (I estimate the length of the fence to be 35m). I will also require a sliding gate that will open/close in my drive way that leads into my double garage.
We require the current palisade fence to be cut to allow a gate to be inserted - new support posts cemented in and the gate needs to be manufactured to the size of the opening (Approx. mm) electric fence must be re-fitted following the profile of the gate. Heavy duty hinges and sliding latch to be used with a tamper proof piece of metal welded on the outside covering the latch area
I am looking for an Easyview fencing quote to secure the perimeter of erf 95 Cato Ridge. See attached diagrams. Perimeter is .9m My client is looking for quotes and I have suggested a medium security 3x4mm clearview fence with square posts to keep out land invaders. Alternate high security as an option would be welcome. The site is inland but does experience damp conditions, please specify metal treatment, powder , galvanised etc. Please also specify options with respect to height. When ready to commence the corners of the site will be pegged out for the contractor as well as inline pegs as needed.
The aperture is 6.5m in total. There are two existing upright walls that the fencing may be attached to. Alternatively, if that is not possible, then it would require three posts in total, but I would have to get your advice on that. I would like it installed as well. The fence will be replacing the broken sections of the wall - as in the pictures attached. It is a section of a perimeter wall that must be replaced with a fence. The height should be between 1m and 1.2 metres. Ideally I would like a representative to come and give me a quote.
Please email me. I will be able to reply immediately, I am not able to take calls. I am looking to install a small fence on top of a wall, it needs to be tall enough to stop a dog from jumping over it or being able to escape. I am not too sure about the length of then fence I would need someone to come take proper measurements.
Item Description 1 Palisade Fencing - .4 linear meters (49.6m x 31.6m x 49.6m x 31.6m) Acquisition of the materials and items - 2 Meters 60 x 60mm x 2 – 2.5mm steel angle iron with 2.5mm width. - 2.5 Meters 76 x 76 x 1.6mm square poles tubes with 2.5mm width. - 60 x 60 x 2 – 2.5mm top and bottom crossing steel angles. - Security padlock for the gate - Welding or casting of the locking mechanisms at the gate. 2.2 Height of the fence - The height of the fence must be two (2) Meters from the ground - Length of the poles must be 2.5 Meters - mm of the 76 x 76 x 1.6mm poles must be dig or excavated into the ground with concrete. - Poles must be 2 meters away from each other. 2.3 Spacing of the poles and angles. - Spacing in between the 60mm angles must be approximately mm. - The 60 x 60 x 2 – 2.5 mm angle iron must have industrial spike on top. - 70mm poles must be covered and closed with the palisade cap. 2.4 Sliding Gate of the palisade fencing - Size of the gate must be 3 Meters wide and slide. - The gate must be fitted with the 60 mm angle iron track. - The sliding track must be fitted with the stop at the end. - The sliding angle iron must have an allowance of 3.5 meters on one side to enable full slide of the gate. - Gate must be installed to enable sliding. - Must have sliding wheels. - Mechanism to lock and protected lock. - Provide security padlock with three (03) keys. 2.5 Painting of the fence - First coat : Prime coat (black or red) - Second coat: Enamel Paint Blue 2.6 Locking mechanisms - Make a mechanism to enable the fitting of padlock - Provide a security padlock 2.7 Crossing angle iron - Slotted channel must be used for the crosses. - Crossing slotted angle iron must be 60 X 60 x 2- 2.5mm - Crossing angle iron must be welded firmly. 1.8 Size and the construction of the palisade fencing Size of the palisade fencing shall be 49.6m x 31.6m x 49.6m x 31.6m and will be constructed around the prefab building.
The boundary measures 49, excluding the two 1m gates. We will opt for the 3mm wire, 1.8m high fence. 75x50 aperture. Dipped black color. Please can you quote on both the prefabricated fence posts and the standard square tubing with clips. We will need 18x 3m panels 23x posts 2x gates (1m width X 1.8m height) At this point we will likely do self installation, however you are welcome to quote on install if you would like to.